diamond sa via dei patrizi 5 ch-6616 losone tel. ++41-91/785 45 45 fax ++41-91/785 45 00 e-mail: info@diamond-fo.com diamond fiber optic components description the preterminated pigtails or patchcords of diamond are products which allow the customer to choose the needed connector at the moment of the installation without loss of quality thanks to the technology of the diamond's "alberno". offering a complete range of solutions,this technology is the right one for applications that presents different kind of connectors, simplifying cabling and allowing a great reduction of very expensive material storage. use laser manufacturer, plumbers, system manufacturer, system integrators, telcommunication, catv, lan ... design the patchcord/pigtail design is based on following components: - pc or apc prepolished "alberino" for: e-2000 or sc or fc or st connectors. ferrule material: zirconia/copper-nickel alloy insert (pilzferrule) - standard cable boot of pur plastic. - fiber/cable of your choice. l "alberino" preterminated patchcords without connector body single mode pc/apc multimode pc specifications subject to change without notice 002-037-207p003073 specifications: standard multimode single mode single mode 8 apc units test conditions insertion loss (il) typ 0.15 max 0.5 typ 0.2max 0.5 typ 0.2 max 0.5 db iec 1300-3-4; = 1300/1550nm return loss (rl) typ 40 50 min 70* db iec 1300-3-6; = 1300/1550nm repeatability of il max 0.1 max 0.1 max 0.1 db over service life service life 1000 mate/demate cycles operating temperature -40 / +85 c storage temperature -40 / +90 c strain relief (cable) > 100 n * measured with high resolution reflectometer hp 8504a may be further limited by cable specifications
123 4 123 4 123 4 order number codes 1 connector code 2 connector code for termination on other end of assembly - for pigtails: insert 000 - for patch assemblies: insert connector code for other connector 3 code for fiber or cable 4 length in meters see ordering information for additional details order information pigtails/patchcords single mode type designation: alb-s0.66 polish geometry: convex (pc) dimensions order number fiber/cable unterminated connector terminated assembly 9/125/900 2 9 0 - 0 0 0 - 0 0 1 l 0 0 0 2 9 0 - x x x - 0 0 1 l x x x 9/125/900/2100 2 9 0 - 0 0 0 - 0 0 2 l 0 0 0 2 9 0 - x x x - 0 0 2 l x x x 9/125/900/2500 2 9 0 - 0 0 0 - 0 0 3 l 0 0 0 2 9 0 - x x x - 0 0 3 l x x x 9/125/900/3000 2 9 0 - 0 0 0 - 0 0 4 l 0 0 0 2 9 0 - x x x - 0 0 4 l x x x 9/125/900/3500 2 9 0 - 0 0 0 - 0 0 5 l 0 0 0 2 9 0 - x x x - 0 0 5 l x x x connectors for other fiber and cable dimensions available upon request multimode type designation: alb-m0.66 polish geometry: convex (pc) dimensions order number fiber/cable unterminated connector terminated assembly 50/125/900 2 9 1 - 0 0 0 - 0 0 1 l 0 0 0 2 9 1 - x x x - 0 0 1 l x x x 50/125/900/2100 2 9 1 - 0 0 0 - 0 0 2 l 0 0 0 2 9 1 - x x x - 0 0 2 l x x x 50/125/900/2500 2 9 1 - 0 0 0 - 0 0 3 l 0 0 0 2 9 1 - x x x - 0 0 3 l x x x 50/125/900/3000 2 9 1 - 0 0 0 - 0 0 4 l 0 0 0 2 9 1 - x x x - 0 0 4 l x x x 50/125/900/3500 2 9 1 - 0 0 0 - 0 0 5 l 0 0 0 2 9 1 - x x x - 0 0 5 l x x x connectors for other fiber and cable dimensions available upon request single mode apc convex type designation: alb-s8.66 polish geometry: 8 angled convex (apc) dimensions order number fiber/cable unterminated connector terminated assembly 9/125/900 2 9 2 - 0 0 0 - 0 0 1 l 0 0 0 2 9 2 - x x x - 0 0 1 l x x x 9/125/900/2100 2 9 2 - 0 0 0 - 0 0 2 l 0 0 0 2 9 2 - x x x - 0 0 2 l x x x 9/125/900/2500 2 9 2 - 0 0 0 - 0 0 3 l 0 0 0 2 9 2 - x x x - 0 0 3 l x x x 9/125/900/3000 2 9 2 - 0 0 0 - 0 0 4 l 0 0 0 2 9 2 - x x x - 0 0 4 l x x x 9/125/900/3500 2 9 2 - 0 0 0 - 0 0 5 l 0 0 0 2 9 2 - x x x - 0 0 5 l x x x connectors for other fiber and cable dimensions available upon request housing description material order number e-2000 pc plastic blue 0 7 0 - 5 0 1 - 0 9 9 v 1 0 1 e-2000 apc* plastic green 0 7 0 - 5 0 1 - 0 9 9 v 2 0 2 sc pc plastic blue** 0 7 0 - 0 2 5 - 1 2 8 v 0 0 1 sc apc* plastic green** 0 7 0 - 0 2 5 - 1 2 8 v 0 0 2 fc pc (2.14 mm)* metal, plastic black** 0 7 0 - 0 2 5 - 1 2 4 v 0 11 fc apc (2.14 mm)* metal, plastic black** 0 7 0 - 0 2 5 - 1 2 4 v 0 12 fc apc (2 mm)* metal, plastic red** 0 7 0 - 0 2 5 - 1 2 4 v 0 2 2 st pc/apc plastic black** 0 7 0 - 0 2 5 - 1 2 6 v 0 0 1 * for the angled connectors the position of the ferrule assembly is given by keeping the black stipe on the back end at the same side as the antirotation key ** protection caps available upon request. tools description order number e-2000 pliers for housing assembly 2 2 1 - 1 0 0 - 0 3 2 v 0 0 1 sc pliers for housing assembly 2 2 1 - 1 0 0 - 0 4 1 v 0 0 1 fc pliers for housing assembly 2 2 1 - 1 0 0 - 0 9 3 v 0 0 1 st pliers for housing assembly 2 2 1 - 1 0 0 - 0 9 4 v 0 0 1
|